Wissensdatenbank
Buehl, Kevin
11 Oktober 2017
22 November 2017
2.220

Wissensdatenbank

Cisco Switch auf Werkseinstellungen zurücksetzen

flash_init
Initializing Flash...
flashfs[0]: 604 files, 19 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 32514048
flashfs[0]: Bytes used: 8337920
flashfs[0]: Bytes available: 24176128
flashfs[0]: flashfs fsck took 10 seconds.
...done Initializing Flash.
Boot Sector Filesystem (bs) installed, fsid: 3
Setting console baud rate to 9600...
load_helperdir flash:
Directory of flash:/

2 -rwx 556 <date> vlan.dat
3 -rwx 5 <date> private-config.text
5 -rwx 2551 <date> config.text
7 drwx 192 <date> c2960-lanbase-mz.122-35.SE5

24176128 bytes available (8337920 bytes used)
rename flash:config.text flash:config.old
boot
Loading "flash:c2960-lanbase-mz.122-35.SE5/c2960-lanbase-mz.122-35.SE5.bin"...@@@@@@
File "flash:c2960-lanbase-mz.122-35.SE5/c2960-lanbase-mz.122-35.SE5.bin" uncompressed and installed, entry point: 0x3000
executing...

Restricted Rights Legend

Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.

cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706



Cisco IOS Software, C2960 Software (C2960-LANBASE-M), Version 12.2(35)SE5, RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Thu 19-Jul-07 20:06 by nachen
Image text-base: 0x00003000, data-base: 0x00D40000

Initializing flashfs...

flashfs[1]: 604 files, 19 directories
flashfs[1]: 0 orphaned files, 0 orphaned directories
flashfs[1]: Total bytes: 32514048
flashfs[1]: Bytes used: 8337920
flashfs[1]: Bytes available: 24176128
flashfs[1]: flashfs fsck took 1 seconds.
flashfs[1]: Initialization complete....done Initializing flashfs.

POST: CPU MIC register Tests : Begin
POST: CPU MIC register Tests : End, Status Passed

POST: PortASIC Memory Tests : Begin
POST: PortASIC Memory Tests : End, Status Passed

POST: CPU MIC interface Loopback Tests : Begin
POST: CPU MIC interface Loopback Tests : End, Status Passed

POST: PortASIC RingLoopback Tests : Begin
POST: PortASIC RingLoopback Tests : End, Status Passed

POST: PortASIC CAM Subsystem Tests : Begin
POST: PortASIC CAM Subsystem Tests : End, Status Passed

POST: PortASIC Port Loopback Tests : Begin
POST: PortASIC Port Loopback Tests : End, Status Passed

Waiting for Port download...Complete

cisco WS-C2960G-24TC-L (PowerPC405) processor (revision E0) with 61440K/4088K bytes of memory.
Processor board ID FOC1302U00S
Last reset from power-on
1 Virtual Ethernet interface
24 Gigabit Ethernet interfaces
The password-recovery mechanism is enabled.

64K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address : 00:48:42:00:48:42
Motherboard assembly number : 00-00000-06
Power supply part number : 000-0000-02
Motherboard serial number : 4B423021WYT
Power supply serial number : AZS00000000
Model revision number : E0
Motherboard revision number : A0
Model number : WS-C2960G-24TC-L
System serial number : FOC1302U00S
Top Assembly Part Number : 800-26673-03
Top Assembly Revision Number : B0
Version ID : V03
CLEI Code Number : COM3G00BRB
Hardware Board Revision Number : 0x01


Switch Ports Model SW Version SW Image
------ ----- ----- ---------- ----------
* 1 24 WS-C2960G-24TC-L 12.2(35)SE5 C2960-LANBASE-M




Press RETURN to get started!


00:00:44: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to down
00:00:44: %SPANTREE-5-EXTENDED_SYSID: Extended SysId enabled for type vlan
00:01:05: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C2960 Software (C2960-LANBASE-M), Version 12.2(35)SE5, RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Thu 19-Jul-07 20:06 by nachen
00:01:08: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/1, changed state to up
00:01:10: %LINK-3-UPDOWN: Interface GigabitEthernet0/1, changed state to up
00:01:39: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to up

Would you like to terminate autoinstall? [yes]:


--- System Configuration Dialog ---

Would you like to enter the initial configuration dialog? [yes/no]:
% Please answer 'yes' or 'no'.
Would you like to enter the initial configuration dialog? [yes/no]: n



Switch>
en
Switch#






rename flash:config.old flash:config.text
Destination filename [config.text]?

copy flash:config.text system:running-config
Destination filename [running-config]?

2551 bytes copied in 0.235 secs (10855 bytes/sec)




conf t
Enter configuration commands, one per line.  End with CNTL/Z.


Nun kann das Passwort gesetzt werden:
enable secret Start2017!
enable password Start2017$
line con 0
password Start2017!
exit


copy run start
Building configuration...
00:16:41: %SYS-5-CONFIG_I: Configured from console by console[OK]




  The enable secret is a password used to protect access to
privileged EXEC and configuration modes. This password, after
entered, becomes encrypted in the configuration.
Enter enable secret:

The enable password is used when you do not specify an
enable secret password, with some older software versions, and
some boot images.

The virtual terminal password is used to protect
access to the router over a network interface.
Enter virtual terminal password: Start2017#